Complete Command Reference | infrADAC BCAD Offline Help

1Find a command

Browse the commands supported by infrADAC BCAD, then choose a row to open the full task guide.

Command names are case-insensitive

You can type command names using upper- or lower-case letters. The reference shows the spelling used in the interface.

2commands

Icon	Command	Purpose
CMD	`ADACAbout`	Open the disclaimer and product acknowledgement.
CMD	`ADACAnnotate`	Create an Annotation enhancement
CMD	`ADACAssetAttributes`	Set reusable Standard and Supplementary asset-specific prefills and optionally load or save a preset JSON.
CMD	`ADACAudit`	Audit the current project
CMD	`ADACBulkBreakline`	Create Breakline assets from linework
CMD	`ADACBulkContour`	Create Contour assets from constant-elevation linework
CMD	`ADACBulkEasement`	Create Easement assets from closed areas
CMD	`ADACBulkLot`	Create Lot assets from closed areas
CMD	`ADACBulkSpot`	Alias for Bulk Spot Height
CMD	`ADACBulkSpotHeight`	Create Spot Height assets from points or blocks
CMD	`ADACClean`	Run selected data-integrity, supporting-file, prefill and property-block repairs.
CMD	`ADACClone`	Clone to points or compatible geometry in BCAD
CMD	`ADACCSV`	Import coordinate rows from supported CSV layouts and map each row to an asset type.
CMD	`ADACCUIx`	Install, reset or remove the BCAD CUIX ribbon.
CMD	`ADACDimension`	Create a Dimension enhancement
CMD	`ADACDirectionClear`	Clear direction metadata and preview graphics.
CMD	`ADACDirectionSet`	Write direction metadata for selected line or surface assets.
CMD	`ADACDirectionView`	Preview selected line or surface direction without writing metadata.
CMD	`ADACDrawingExtents`	Set project drawing extents
CMD	`ADACEdit`	Edit selected assets in BCAD
CMD	`ADACErrorHide`	Hide selected or all transient audit highlights without deleting them.
CMD	`ADACErrorShow`	Show selected or all stored transient audit highlights.
CMD	`ADACErrorWipe`	Remove selected or all transient audit highlights.
CMD	`ADACExport`	Audit and export supported deliverables
CMD	`ADACFind`	Search current design assets and focus the exact result
CMD	`ADACFlowDirection`	View, set, compare or clear fall-direction metadata for selected linework.
CMD	`ADACGenerate`	Create or assign a compatible definition from existing geometry
CMD	`ADACGlobalAttributes`	Set or edit category-based global attribute presets for later asset workflows.
CMD	`ADACGroundCreate`	Build and activate an infrADAC ground surface from supported source data.
CMD	`ADACGroundDefine`	Activate a stored or selected existing ground surface.
CMD	`ADACGroundReset`	Clear the active ground-surface definition and optionally delete generated geometry.
CMD	`ADACHelp`	Open the bundled product-specific offline HTML manual in the dedicated infrADAC User Manual window.
CMD	`ADACHideAttributes`	Hide selected or all asset property blocks.
CMD	`ADACImport`	Audit and import an ADAC XML file
CMD	`ADACLibrary`	Browse and edit profile-backed definitions, geometry, required-status rules and the appearance controls supported by the active product.
CMD	`ADACLicence`	Review, refresh, check out, return or troubleshoot the active licence.
CMD	`ADACLog`	Open the latest infrADAC diagnostic log.
CMD	`ADACNew`	Run project, global and asset-prefill initialisation
CMD	`ADACProfile`	Edit the current profile metadata and supplementary contents; host-specific drawing resources remain product-limited.
CMD	`ADACProject`	Edit project location, profile, standard, name and description.
CMD	`ADACProjectAttributes`	Set profile-controlled project attributes
CMD	`ADACRecreateAttributes`	Recreate property blocks for selected assets or groups.
CMD	`ADACRefreshAttributes`	Refresh selected or all property blocks from current XData.
CMD	`ADACSettings`	Open general, profile, licence, update and folder settings.
CMD	`ADACShowAttributes`	Show selected or all asset property blocks.
CMD	`ADACStandard`	Choose and create a standard asset from the active profile or base schema.
CMD	`ADACSupplementary`	Choose and create a supplementary asset from the active profile.
CMD	`ADACSupport`	Create a support ticket and optionally attach the latest log.
CMD	`ADACSurface`	Open the land and surface action menu.
CMD	`ADACUpdate`	Check software and entitled profile updates.
CMD	`ADACXData`	Inspect all registered XData on selected infrADAC assets.
CMD	`ExtractBlockAttributes`	Diagnostic helper for extracting block attributes inside a selected area.
CMD	`ExtractPolylineXData`	Diagnostic helper for checking infrADAC polyline XData inside a selected area.

3Selection behaviour

Product	How selection works
BCAD	Uses the same preselection pattern through BricsCAD selection APIs.

1Find a command

2commands

3Selection behaviour

4Related guides